OVERHEAD NETWORKS

OVERHEAD NETWORKS

CHALLENGER – DRILLING CRANES – LIFTING CRANES – WINCHES

All our equipment is accompanied by a commissioning by the manufacturer on the customer’s site

Mise en service du Challenger 8 en Normandie.

CHALLENGER 8

  • CUMMINS QS 4.5 Turbo Diesel engine, 173 hp at 2,200 rpm, 780 nm at 1,500 rpm
  • Fuel tank 230 L + 1 ADBlue 30 L tank
  • LOAD SENSING controlled hydraulics
  • Automatic thermal accelerator
  • Full box-section chassis
  • Heated, ventilated and soundproofed cabin
  • Braked front and rear axles, 10,000 kg dynamic unit load
  • 24″ four-wheel drive and steering
  • Slewing ring (ø 1000 mm)
  • Lifting capacity 20 t.m to 24 t.m
  • Two independently controlled telescopes, optional integrated extension
  • Drilling motor, 1,600 m.kg on 1st telescope
  • Side plate for tools
  • Front and rear stabilizers with integral folding
  • Control of front and rear stabilisers from the cab or by radio control (optional)
  • Transport capacity 4 T x 2 or 3 and 5 T
  • Pivoting rear post holders
  • Overall length 7 m, overall height 3.45 m

Watch the CHALLENGER 8 video

icone_fiche
icone_tel
icone_mail

LES DIFFÉRENTS ÉQUIPEMENTS SELON LES TYPES DE CHALLENGER 8

TYPE

Crane type
Torque
Carrier motor
Full led lighting
Extendable pole holder
Backhoe pre-equipment
Tilt adjustment
Hydraulic towing winch
Radio control
Radio control stabs
Headlight protection
Low trunk
Hydraulic auger release
Fuel tank filling pump
Extension integrated in the telescope

8S – Export –

TA60.33
20t.m
130 CV E3
NON
NON
NON
NON
NON
OPTION
OPTION
OPTION
OPTION
NON
OPTION
NON

8SR7

74TA30
22t.m
173 CV
OPTION
OUI
OUI
OPTION
OPTION
OUI
OPTION
OPTION
OPTION
OUI
OPTION
OPTION

8SR8

80TA30
24t.m
173 CV
OPTION
OUI
OUI
OPTION
OPTION
OUI
OPTION
OPTION
OPTION
OUI
OPTION
OPTION

8SRT

80TA30
24t.m
173 CV
OUI
OUI
OUI
OUI
OUI
OUI
OUI
OUI
OUI
OUI
OUI
OUI

icone_fiche
icone_tel
icone_mail
icone_tel
icone_mail
Foreuse tarière grue G2T grue de levage grue de forage marteau fond de trou

G2T

Lifting 2 t to 3.5 m on 1 strand
Lifting 4 t to 2.50 m with a block (optional)

  • Kinematics with 1 articulated arm and 1 telescope
  • Lifting winch with load-holding valve: 2 t in 1st layer, high and low limit switches Hook height 8 m
  • Maximum horizontal reach: 6, 15 m
  • Drilling distance: 3, 10 m to 5.80 m
  • Reduced lifting range on 235° FWD with electronic limiter (depending on mounting)
  • LEDs for display of lift rates (90%, 100%, 110%)
  • Continuous and unlimited 360° rotation by crown wheel with internal teeth, gear motor with no-pressure brake, equipped with double load-holding valve
  • Drill motor, torque 1,000 m/kg, R and L rotation, hex drive of 0 70 mm
  • Auger support device on the 1st telescope
  • Radio control of 2 batteries and a charger in the cabin with remote start and stop and 2 speed control screen
  • Stabilizers control on radio
  • Automatic acceleration of the engine for each movement
  • Electronic load limiter
  • Optional down-the-hole hammer
icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail
Grue de levage tarière grue de forage camion gruegrue_de_forage_RISA_G2T_ECO.KPL

G2T ÉCO

Lifting 2 t to 3.5 m on 1 strand
Lifting 4 t to 1.50 m with a block (optional)

    • Kinematics with 1 articulated arms and 1 individually controlled telescopes
    • Turret rotation limited to 2 times 200° by crown wheel of Ø825 with internal teeth, gear motor with no-pressure brake, equipped with double load-holding valve
    • Lifting cylinder with double-acting load-holding valve
    • Telescope cylinder with balancing valve
    • Lifting winch with load-holding valve: 2,000 kg in 1st layer, high and low limit switches
    • Height under hook of 8.20 m
    • Maximum horizontal reach: 6.15 m
    • Drilling distance: 3.10 m to 5.80 m
    • Lifting range at full load on 360° (depending on mounting)
    • Emergency stop on the driver’s platform
    • Hydraulic load limiter as standard
    • Pressure gauge load display
    • Dispenser protection devices, spirit level, etc.
    • Crane controls via stepless valves at the operator’s station at the foot of the turret
    • Drill motor, torque 1,000 m/kg, R and L rotation, hexagon drive of Ø 70 mm
    • Auger support device permanently mounted on the telescope
    • Controls for all crane functions (rotation, 1st arm, telescope, winch, drilling)
    • 1 operating speed
    • Automatic acceleration of the engine for each movement
icone_tel
icone_mail
icone_tel
icone_mail
UGE 530 Bohrgerät Frankreich

GRUE 74TA30

lifting 7.4t at 3m / capacity 22t/m

    • Kinematics with 2 articulated arms and 2 individually controlled telescopes
    • Hook height 12 m (13.80 m with integrated lift extension)
    • Lifting range at full load is 360° (depending on mounting)
    • LEDs for display of lifting rates (90%, 100%, 110%)
    • Continuous and unlimited 360° rotation by means of a 1000 mm diameter crown wheel with internal gearing, gear motor with no-pressure brake
    • High station on turret with removable double seat
    • Proportional distributor with variable flow hydraulic pump
    • Drill motor, torque 1,600 m/kg, R and L rotation, hexagon drive of Ø 0.70 mm
    • Auger support device on the 1st telescope
    • Hydraulic auger release
    • Electronic load limiter as standard
    • Radio control of 2 batteries and a charger in the cabin (Optional)
    • Radio control of stabilizers (Optional)

Découvrez la vidéo de la 74TA30 sur Unimog

icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail
rue radiocommandées grue telecommandee

CRANE 80TA30

lifting 8t at 3m / capacity 24t/m

    • Kinematics with 2 articulated arms and 2 individually controlled telescopes
    • Hook height 12 m (13.80 m with integrated lift extension)
    • Lifting range at full load is 360° (depending on mounting)
    • LEDs for display of lifting rates (90%, 100%, 110%)
    • Continuous and unlimited 360° rotation by means of a 1000 mm diameter crown wheel with internal gearing, gear motor with no-pressure brake
    • High station on turret with removable double seat
    • Proportional distributor with variable flow hydraulic pump
    • Drill motor, torque 1,600 m/kg, R and L rotation, hexagon drive of Ø 0.70 mm
    • Auger support device on the 1st telescope
    • Hydraulic auger release
    • Electronic load limiter as standard
    • Radio controls 2 batteries and a charger in the cabin with remote stop and start and control screen
    • Radio control of stabilizers
icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail
rue radiocommandées grue telecommandee

CRANE 86TA30

lifting 8.6t at 3m / capacity 26t/m

    • Kinematics with 2 articulated arms and 2 individually controlled telescopes
    • Hook height 11.80 m (13.60 m with integrated lift extension)
    • Lifting range at full load is 360° (depending on mounting)
    • LEDs for display of lifting rates (90%, 100%, 110%)
    • Continuous and unlimited 360° rotation by means of a 1200 mm diameter crown wheel with internal gearing, gear motor with no-pressure brake
    • High station on turret with removable double seat
    • Proportional distributor with variable flow hydraulic pump
    • Drill motor, torque 1,600 m/kg, R and L rotation, hexagon drive of Ø 0.70 mm
    • Auger support device on the 1st telescope
    • Hydraulic auger release
    • Electronic load limiter as standard
icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail
Grue de levage/forage Risa 100TA30

CRANE 100TA30

lifting 10t at 3m / capacity 30t/m

    • Kinematics with 2 articulated arms and 2 individually controlled telescopes
    • Hook height 11.80 m (13.60 m with integrated lift extension)
    • Lifting range at full load is 360° (depending on mounting)
    • LEDs for display of lifting rates (90%, 100%, 110%)
    • Continuous and unlimited 360° rotation by means of a 1200 mm diameter crown wheel with internal gearing, gear motor with no-pressure brake
    • High station on turret with removable double seat
    • Proportional distributor with variable flow hydraulic pump
    • Drill motor, torque 1,600 m/kg, R and L rotation, hexagon drive of Ø 0.70 mm
    • Auger support device on the 1st telescope
    • Hydraulic auger release
    • Electronic load limiter as standard
    • Radio controls 2 batteries and a charger in the cabin with remote stop and start and control screen
    • Radio control of stabilizers
icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail
rue radiocommandées grue telecommandee

G2T

Lifting 2 t to 3.5 m on 1 strand
Lifting 4 t to 2.50 m with a block (optional)

    • Kinematics with 1 articulated arm and 1 telescope
    • Lifting winch with load-holding valve: 2 t in 1st layer, high and low limit switches Hook height 8 m
    • Maximum horizontal reach: 6, 15 m
    • Drilling distance: 3, 10 m to 5.80 m
    • Reduced lifting range on 235° FWD with electronic limiter{depending on mounting)
    • LEDs for display of lifting rates (90%, 100%, 11 0%)
    • Continuous and unlimited 360° rotation by crown wheel with internal teeth, gear motor with no-pressure brake, equipped with double load-holding valve
    • Drill motor, torque 1,000 m/kg, R and L rotation, hexagon drive of Ø 70 mm
    • Auger support device on the 1st telescope
    • Radio controls 2 batteries and a charger in the cabin with remote stop and start and control screen 2 operating speeds, stabiliser control
    • Automatic acceleration of the engine for each movement
    • Electronic load limiter
icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail
rue radiocommandées grue telecommandee

G2T ECO

Lifting 2 t to 3.5 m on 1 strand
Lifting 4 t to 1.50 m with a block (optional)

    • Kinematics with 1 articulated arms and 1 individually controlled telescopes
    • Turret rotation limited to by crown wheel of 825 with internal teeth, gear motor with no-pressure brake, equipped with double load-holding valve
    • Lifting cylinder with double-acting load-holding valve
    • Telescope cylinder with balancing valve
    • Lifting winch with load-holding valve: 2,000 kg in 1st layer, high and low limit switches
    • Height under hook of 8 m
    • Maximum horizontal reach: 6.15 m
    • Drilling distance: 3.10 m to 5.80 m
    • Lifting range at full load on 360° AR (depending on mounting)
    • Emergency stop on turret near the driver’s platform
    • Pressure gauge load display
    • Dispenser protection devices, spirit level, etc.
    • Crane controls via stepless valves on turret at the foot of the turret.
    • Drill motor, torque 1,000 m/kg, R and L rotation, hexagon drive of Ø 70 mm
    • Auger support device permanently mounted on the telescope
    • Controls for all crane functions (rotation, 1st arm, telescope, winch, drilling)
    • 1 operating speed
    • Automatic acceleration of the engine for each movement
    • Hydraulic load limiter as standard
icone_tel
icone_mail
icone_tel
icone_mail
Grue de levage/forage TA80.26 en dos de cabine

CRANE TA80.26

Lifting 8t at 2.6m / capacity 21t/m

    • Integral folding with drill motor fixed in the carrier’s frame
    • Kinematics with 2 articulated arms and 2 individually controlled telescopes
    • Rotation by turret with crown Ø 1,000 mm, motor reducer of orientation equipped with a safety brake by absence of pressure
    • Height under hook 10,70 m (integrated extension 12,70 m 1 000 kg)
    • Height under hook 10,70 m (integrated extension 12,70 m 1 000 kg)
    • Lifting range varies depending on the type of carrier used
    • Cut-off load limiter strictly in accordance with the chart in all positions
    • Emergency stops
    • LEDs for display of lifting rates (90%, 100%, 110%)
    • Dispenser protection devices, spirit level, etc.
    • Drilling motor FR. 1 100 (radial hydraulic torque 1 100 m kg) on the 1st telescope (foldable in the jig), hexagon Ø 70 mm and rotation D/G
    • Radio control, with box in belt, 1 charger in cabin + 1 set of extra batteries + remote start
icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail
rue radiocommandées grue telecommandee camion grue

CRANE 100TA30

Lifting 10t at 3m / capacity 30t/m

    • Kinematics with 2 articulated arms and 2 individually controlled telescopes
    • Hook height 11.80 m (13.80 m with integrated lift extension)
    • LEDs for display of lifting rates (90%, 100%, 110%)
    • Continuous and unlimited 360° rotation by means of a ø 1200 mm crown wheel
    • Drill motor (optional) rotation D and G, hex drive of ø 0.70 mm
    • Electronic load limiter as standard
    • Radio controls 2 batteries and a charger in the cabin with remote stop and start and control screen
    • Automatic accelerator for the combustion engine
icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail
BOXER TREUIL DE TIRAGE HTB

BOXER 4

    • HTB line railing winch in compliance with lifting standards
    • CUMMINS QSB 4.5 Turbo Diesel engine, 160 hp at 2200 rpm, 624 nm at 1500 rpm
    • Hydrostatic transmission with automotive control, 4× 2 (0 to 25 km/h) / 4× 4 (0 to 10 km/h) – construction mode (0 to 3 km/h)
    • Electro-hydraulic rear wheel steering in the cabin
    • Reinforced forestry wheels, valve protection tyres
    • Front and rear motorised steering axles. Load 10t, hydraulic locking
    • Rear tow hitch
    • Hydraulic tool socket 30 l/140 bar
    • Approved central cab with 2 sliding doors
    • Front and rear cab protection arch made of heavy section steel tubes and grilles
    • Safe access to the cabin and winch by guardrails and handrails
    • Rotating seat on rotating console for reversed position
icone_fiche
icone_tel
icone_mail
icone_fiche
icone_tel
icone_mail